基于CH自由基发光的旋流火焰放热率时空特性研究

对不同工况下CH4/air旋流火焰的放热率在时间上的热声振荡现象和空间的三维形态转变两方面进行了研究。在燃烧形态转变方面，由于旋流火焰的复杂流场分布特性，采用基于化学自发光的三维计算层析技术(3D-CTC)，测量了雷诺数从5 000到20 000的三个工况下旋流燃烧的CH*发光三维火焰结构。以此表征放热率的三维分布，实现对旋流火焰放热空间形态的测量。该诊断方法通过对旋流火焰发光在8个视角下的二维成像，结合层析重建算法得到其三维CH*分布信息。为验证重建保真度，将重建后结果二维可视化与高速摄影下的二维时均结果进行对比，结果表明重建误差在5%以内。研究中，分析了不同雷诺数下放热率的空间变化规律，结果显示所有实验工况下放热率的垂直于喷嘴方向的变化程度比沿喷嘴轴向的要剧烈；而随着雷诺数增加，最大的放热区表现出了明显的向后推进趋势。在旋流燃烧的热声振荡方面，利用CH*的二维高速摄影，对旋流燃烧的放热率不稳定性进行研究，发现放热率的振荡频率随着雷诺数的增大逐渐增加。      

等离子体助燃下超燃支板燃烧室燃烧特性数值研究

为了将支板喷注器与等离子体射流这两种促进超声速燃烧室燃烧的方式结合起来,设计了一种带有等离子体射流喷孔的支板燃烧室,并在超声速来流的条件下,针对燃料喷注总压、燃料喷注位置、等离子体射流介质、等离子体射流总压对燃烧室燃烧性能的影响进行了三维数值模拟。研究发现:增大燃料的喷注总压,燃烧室的燃烧范围明显增大,燃烧效率呈现出先增大后减小的趋势,在燃料喷注总压为2.0MPa时,燃烧效率达到最大值90.4%;不同的燃料喷注位置对燃烧室的燃烧范围影响较小;等离子体射流介质为O2时,燃烧效率最高,燃烧范围最广;提高等离子体射流的喷注总压,能够提升凹腔剪切层高度,有效促进燃烧,但同时也带来了更高的总压损失。     

Aerodynamic performance enhancement for flapping airfoils by co-flow jet

Introducing active flow control into the design of flapping wing is an effective way to enhance its aerodynamic performance. In this paper, a novel active flow control technology called Co-Flow Jet (CFJ) is applied to flapping airfoils. The effect of CFJ on aerodynamic performance of flapping airfoils at low Reynolds number is numerically investigated using Unsteady Reynolds Averaged Navier-Stokes (URANS) simulation with Spalart-Allmaras (SA) turbulence model. Numerical methods are validated by a NACA6415-based CFJ airfoil case and a S809 pitching airfoil case. Then NACA6415 baseline airfoil and NACA6415-based CFJ airfoil with jet-off and jet-on are simulated in flapping motion, with Reynolds number 70,000 and reduced frequency 0.2. As a result, CFJ airfoils with jet-on generally have better lift and thrust characteristics than baseline airfoils and jet-off airfoil when C_μ is greater than 0.04, which results from the CFJ effect of reducing flow separation by injecting high-energy fluid into boundary layer. Besides, typical kinematic and geometric parameters, including the reduced frequency and the positions of the suction and injection slot, are systematically studied to figure out their influence on aerodynamic performance of the CFJ airfoil. And a variable C_μ jet control strategy is proposed to further improve effective propulsive efficiency. Compared with using constant C_μ, an increase of effective propulsive efficiency by 22.6% has been achieved by using prescribed variable C_μ for NACA6415-based CFJ airfoil at frequency 0.2. This study may provide some guidance to performance enhancement for Flapping wing Micro Air Vehicles (FMAV).     

Numerical simulations of turbulent flows in aeroramp injector/gas-pilot flame scramjet

To uncover the internal flow characteristics in an ethylene-fueled aeroramp injector/gaspilot(ARI/G-P)flame scramjet,a Reynolds-averaged Navier-Stokes(RANS)solver is constructed under a hybrid polyhedral cell finite volume frame.The shear stress transport(SST)k-x model is used to predict the turbulence,while the Overmann’s compressibility corrected laminar flamelet model is adopted to simulate the turbulent combustion.Nonreactive computations for Case 1(G-P jet on),Case 2(ARI jets on),and Case 3(both ARI and G-P jets on)were conducted to analyze the mixing mechanism,while reactive Cases 4–7 at equivalent ratios of 0.380,0.278,0.199 and0.167 respectively were calculated to investigate the flame structure and combustion modes.The numerical results are compared well to those of the experiments.It is shown that the G-P jet plays significant role in both the fuel/air mixing and flame holding processes;the combustion for the four reactive cases takes place intensively in the regions downstream of the ARI/G-P unit;Cases 4 and 5are under subsonic combustion mode,whereas Cases 6 and 7 are mode transition critical and supersonic combustion cases,respectively;the mode transition equivalent ratio is approximately 0.20.     

非恒定增压式微尺度拉瓦尔喷管流动特性

针对微尺度喷流在航天器运动状态切换时出现的非恒定增压变化,采用直接模拟蒙特卡洛(DSMC)方法对阶跃式增压和线性式增压两种模式下的微尺度拉瓦尔喷管流场进行了模拟,并对其变化过程中的流动特性进行了对比分析。结果显示：阶跃式增压会导致流动特性出现较大幅值的峰谷式波动,而线性式增压下的流动特性则呈现出线性变化的特点;黏性力对微尺度喷流的非恒定增压变化产生了重要的黏滞作用,在喉部扩张段至出口的流场中尤为明显;在设定的条件下,阶跃式增压过程中喷流产生的总冲量较线性式增压高59.5%,质量流量高74.7%,单位工质提供的冲量低约8.6%,波动性也高于线性式模型,阶跃式增压适用于系统需要较大推力改变运动状态且推进剂充足的情况,而线性式增压在系统精确微调或需要推进剂产生更高效能时具有明显的优势。     

鸭式布局飞机矢量喷流对地面效应影响的风洞试验

针对单发鸭式布局飞机，通过低速风洞试验，研究了矢量喷流对飞机地面效应的影响特性。研究结果表明：发动机喷流使得飞机的地面效应增强，升力系数增加，降低飞机起飞/降落时的飞行速度，缩短起降距离，从而改善飞机起降性能。发动机喷管上/下偏转时，矢量喷流对飞机上下表面气流诱导不对称，均使地面效应阻力系数增量减小。在此基础上，基于数值模拟结果对喷流与地面效应的相互作用机理进行了分析。     

低温磨料气射流加工PDMS实验研究

通过自研的低温磨料气射流加工装置进行低温磨料气射流加工聚二甲基硅氧烷(polydimethylsiloxane,PDMS)实验研究,分析了加工时间、加工距离、冲蚀角度和磨料粒径对冲蚀率、孔深和孔横截面形貌的影响。结果表明:随着加工时间的增加,冲蚀率先增大后减小,在第1阶段加工过程中,孔深与加工时间大致呈线性关系,增加加工时间还可使孔底部变平整;存在一个最佳加工距离使孔深最大,当加工距离大于最大加工距离时,孔深将随着加工距离的增加而急剧下降,孔的锥度随着加工距离的增大而增大;当冲蚀角度处于30°～60°之间时,冲蚀率最大,随着冲蚀角度的增加,孔的形状逐步由椭圆形变成圆形;存在一个最佳磨料粒径,使冲蚀率和孔深达到最大;当冲蚀角度小于90°时,低温磨料气射流加工PDMS材料去除机理为塑性去除和脆性去除的结合。     

多段翼混合边界层改变对流场的影响研究

前缘缝翼尾流与主翼边界层混合的改变对主翼气动力具有重要影响.利用数值模拟手段,通过在前缘缝翼尾缘添加一定动量系数的喷流,改变前缘缝翼尾缘的尾流,进而改变尾流与主翼边界层的混合状况.求解二维多段翼模型30P30N在各个不同喷流条件下的二维非定常流场,结果表明:提高前缘缝翼尾缘喷流的动量系数,将使前缘缝翼尾流和主翼边界层混合开始点后移,提高主翼上表面负压峰值和主翼升力;混合开始点对主翼的负压峰值及升力均有一定的影响;增大来流攻角会抑制前缘缝翼尾流和主翼边界层的混合.     

火花放电合成射流与超声速来流相互干扰特性数值模拟研究

为了指导火花放电式合成射流激励器在超声速流动控制中的应用,数值模拟研究了火花放电合成射流与超声速来流的相互干扰特性。研究表明火花放电式合成射流在超声速流场中产生强烈扰动,产生较强的激波结构;随着射流的喷出,激励器上游分离区和流场中激波呈先增强后减弱的趋势,激波由弓形激波逐渐弱化为斜激波,并且随着放电能量的增加射流与主流的动量通量比不断增大,射流的干扰和控制能力显著增强。由于超声速流的较大惯性及其对腔内气体的引射作用,激励器的腔体回填速率大幅下降、回填时间明显增长,使得激励器的工作频率受到很大限制。     

Effects of synthetic jet frequency on the separated flow in a diffusing S-duct

Numerical simulations were carried out to investigate the effects of synthetic jet actuation frequency on the separated flow in a diffusing S-duct. The Reynolds number based on the entrance height was 9.78×105. At first, the numerical model was validated with experimental data, and then, the interaction between the separated flow and the synthetic jets at different frequencies was discussed. The results demonstrate that the control effect is significantly dependent on the momentum mixing enhancement between inside of the separated boundary layer and the outer flow. There exists a narrow range of actuation frequency, in which effective separation control can be achieved using synthetic jets. A dimensionless frequency F+=1.0 is identified as the optimal frequency, with a momentum coefficient of 1.62×10-3, the separation area is reduced about 46%, and the aerodynamic performance of the S-duct is also greatly improved compared to uncontrolled case. Further analysis reveals that the choice of actuation frequency is mainly determined by the momentum flux produced by a single ejection and the spacing between adjacent ejections, the optimal frequency case can be understood as a balance between the two factors. In addition, it is found that the synthetic jets can also suppress the secondary flows while decreasing the separation.